FAQ.ECAT.COM

Could you tell the primary flow rate of the peristaltic pump?

Asked by Ecat.com  water pump

I was wondering, if you increased the hydrogen pressure to a very high level, and then initiated a rapid temperature increase greatly above the ignition temperature, do you think a military-type reaction would result, assuming the enclosure could contain the reaction for some period of time?

Asked by Ecat.com  temperature reaction hydrogen pressure

Are the first units already made with such material so they could withstand 400 degrees? Or will the retrofitting be a complicated process?

Asked by Ecat.com  e-cat development commercialization

How you will solve the off-to-on requirements of a home heater?

Asked by Ecat.com  home heater off-to-on

Did you try to measure a possible perturbation of gravity around the reactor of the e-cat?

Asked by Ecat.com  e-cat gravity reactor

Do you think this technology would one day be scalable to the size of existing conventional nuclear reactors?

Asked by Ecat.com  development technical data

Is the hardware and software for controlling the reaction it implemented on a critical standard (CEI60780, EN50128) respecting the protection of persons?

Asked by Ecat.com  hardware software reaction

Will the commercial e-cat also contain Boron, as described in you patent? Would it be possible exclude the use of Boron in the e-cat concept?

Asked by Ecat.com  patent boron e-cat concept

If I am not wrong,the reaction start at 60 °C

Asked by Ecat.com  temperature

Is it possible to know the daily (24h) power consumption in kwh of the E-Cat at 1/3 of its thermal power (3,3kw), 2/3 (6,7kw) and full power (10kw) without considering the 1 hour start-up consumption?

Asked by Ecat.com  e-cat power consumption thermal power

1. Must the E-Cat be cold before the fuel rod can be safely removed? 2. If so, is there a safety mechanism that is incorporated into the E-Cat that will prevent removal at any other time? 3. Will you continue to work at raising the temperature of the reactor from 260C even though you have achieved this important milestone? 4. What do you believe to be the next milestone for the E-Cat?

Asked by Ecat.com  e-cat fuel safety mechanism

1) Is the returned Ni all, or mostly, available to be reused, after reprocessing, in fresh E-Cat charges? 2) Is there a limit as to how many reprocessing cycles a Ni charge can undergo before it becomes unsuitable for use in an E-cat? 3) If the Ni does become unsuitable at some point, presumably it would still be suitable for general industrial use?

Asked by Ecat.com  ni e-cat charges industrial use

Must the E-Cats in the MW plant be turned off when refuelling every 6 months?

Asked by Ecat.com  e-cats mw plant refuelling

In the MW plant, is every E-Cat automatous? That is, is every E-Cat fully independent with its own control unit? If so, do the E-Cats communicate with each other in order to support each other when the need arises? Example: When an E-Cat is close to exiting the self-sustain mode and needs to be charged anew, does it put out a signal to the other E-Cats for help, and do they respond?

Asked by Ecat.com  e-cats self-sustain mode mw plant

Have you switched the 1MW device off, then on again with satisfactory results?

Asked by Ecat.com  1 mw test

What is the temperature of the output that the 1MW reactor is running at?

Asked by Ecat.com  1 mw temperature

Considering that a home-based E-Cat may not be ideally suited to all domestic situations. Is it possible (maybe within 10-20 years) that we could see large, muli-staged, self-sustaining E-Cat power plants that could replace nuclear power plants? If built next to the existing nuclear reactor buildings, they could even maybe utilise the existing turbines/electicity distribution installations.

Asked by Ecat.com  1 mw

Have you ever thought about inductive/rf heating of the ni powder?

Asked by Ecat.com  heating